Recent content by blazer02

Thanks for the info

I got mine from current river marine but any tohatsu dealer can get them.these are a new design been out since atleast 2012 i know dont no if they're based of the original mega or not but there basically a 50 block that thats detuned to a 40 and run a direct injection fuel system and they are a...

A 25hp jet motor should push a 1448 with two men in it easy if everything is in good working order in the jet and the motor is installed at the proper height.it should make around the 28mph that the alumaweld is making.i ran a 25 horse johnson on a 1848 blazer that loaded down with 250lbs of...

What i have learned through my research so far is i believe these motors both have same ecu but i cant be 100% sure intill i can put my hands on a 35.tohatsu shows the same ecu for both there 40&50 horse tdli prop motors which should be the same power head as this motors use. So anyone know any...

Can i get a 6 1/8 3 blade stainless impeller for a mega 25 tohatsu and if so anyone no where?will motor gain any mph with stainless or not to?

I have been told by a guy that had heard from another guy that if u remove the restricter and put a 35 ecu on a 25 that's it becomes the 35 but i don't no if there is any truth to this or not.i have a brand new mega 25 because i run a lot in a 25 limit zone but i am running a 18 48 blazer and...

Can anyone tell me the exact differences in the tohatsu 25 jet and 35 jet motors.from what little info i gave been able to find these motors both use the same block and basically the same motor except the 25 has a restricter and different throttle body that cut the 50hp power head to 40.I'm...

The 35 is down river with just me in boat and with motor trimmed out As perfect as u can get it.these motors are actually very powerful for there size and with the direct injection and still being 2 stroke they wind up fast and hard.

I have a brand new mega 25 tohatsu i just picked up other day and i have about a hour of run time on it.i got to looking at the lower unit after i took out other day and i noticed the impeller doesn't come with much of a leading edge to it.the motor flat scoots my 18 48 blazer gpsed it making...

Maybe some of the others chime in but if your lip is level with bottom think its a bit low.always been told and run mine with the bottom being level with the front pin in your grates.on your boat with a 30/25 i think it should run right along.I ran with a guy last week running one on a 1742 with...

Don't know if you wanting to travel that far but according to dealer registry they a tohatsu dealer about 70 miles from you i think.was looking back at your post and curious why you running so slow with current setup.I'm running a loaded down 1848 blazer sport floor rod box big livewell around...

I believe the tohatsu's have a adjust on them for low rpm trolling.my buddy that has one traded his 4 stroke in for this one sai glad he did.with the direct injection on these motors they sound and idle like a 4 stroke.

Will second that.Fish sometimes with a goo friend that runs a mega 25 tohatsu on a 1648 blazer.boat is pretty bare deck and small livewell but mean him both in it him in back and me on front deck both about 230 a packed cooler and around 50lb of gear it run a solid 32-34 average down river...

Yeah have to be better than the grooves in one.i run in a lot of low water sometimes and your constantly sucking sand and gravel and you can't be replacing sleeve every couple trips.thought keep a old one or two patched up to use when the water gets low and save ruining a good one time and time...

Mine has a black spacer above the jet around one inch thick i believe it aluminium and its what your talking about.has a bolt that runs through it into jet on the back below exchaust.