Search results

I'm trying to find a top mount binnacle remote control box for a 1996 Suzuki Dt115s EFI. No luck on ebay and can't find any solid info on what aftermarket controls will work. Will a control for a 4stroke suzuki work? How about higher horsepowers? There's one off a 225 hp Suzuki 2-stroke on eBay...

Nice rig, congrats!!

How about putting in the new ones? Any other tool needed? Thanks pappy

1999 115. I need to replace the 2 top seals on the drive shaft bearing housing under the water pump. Do they pop out easy enough and do I need any special tools for the job?

Stayed up half the night surfing web and found one that'll work on mine. Just wanted to post in case it might help someone else. Thanks offshoremarineparts.com/8402-460.html

Glad to hear everyone ok. Would of stained my shorts for sure..

Darn VRO broke, I mean a piece actually broke off so it's wothless now. Anyway, I'd read how countless other vro owners were able to put a standard fuel pump instead and I wanted to do the same ' cause funds are limited. I ordered the new replacement pump (OEM 0438559) just to find out that i...

Thanks TH. is his a mod v or flatbottom?

Getting a 1752 weld-craft tin. I have to use my 30hp 2 stroke till next year when I can afford more power. Not concerned about speed but curious if it would plane with 3 men and light fishing tackle? It's a bare flatbottom that I'll be dropping in a ply-wood floor.

Thanks for the advice guys. I'm scratching the pods but still considering jack plate.

I'm also seeing it as protecting my investment, I sometimes fish back of nueces bay and those oyster beds seem to pop out of nowhere. I have a 1444 alweld now with a mini jacker and like the lift/setback but does cause it to get more back heavy.

I'm looking at a tohatsu 4 stroke which are not that heavy but i do want to run as shallow as i can. Don't want a tunnel so by my research it seems like a setback/jack plate with pods would be the way to go, I just haven't seen too many tiller drives with this setup.

Can you share your opinion on pods on a tiller Jon. I'm getting a 17 or 18' mod v with tiller steering I'll be fishing flats, rivers and crossing a bay here and there. I'm wanting to know if the pods/sponsons would be better than just a stabilizer. It'll be my 9 year old (skinny) son in the...

A Tracker grizzly 1754 is rated for a 30hp max according to their website. Hoping with the right prop it'll be ok but have read conflicting opinions. Kinda confusing cause all other brands I've researched have a higher max rating hp. I have it on a 1444 alweld now and it's really fast with 2...

I have a 30hp nissan tiller and am wondering if it will do ok on a 17' welded Jon. Can't afford new engine and need a bigger boat. At the heaviest It be 3 adults with tackle. Any advice appreciated.

I dunno, the more i research the more confused i get. Top end speed is not that important to me cause im thinking this little boat is going to scoot with any prop within range. I'd would prefer a better whole shot, gonna be doing mostly flats fishing and can get pretty shallow. I was just...

and my boat is smaller than yours (14 x 44) so thats why i was thinking a 13- 4 blade.

It's a 2000 Nissan NS 30A4. When i took it out i noticed it suddenly lost some power on the way back in at wot (going with the waves and wind to my back). Engine seemed fine but had to bring it in cause it was getting dark. checked compression and good with 125ish on both cylinders. I took the...

I have a 30hp long shaft with factory prop (9.8x11.3pitch). This prop is dead center in the recommended range of props according to the owners manual, it starts with 14p for "lighter boats" and down to 8p for "heavier boats". I have it on a 14x44 alweld mod v (21"transom). It's pretty darn light...

gonna take a trip to west marine, called over there and they have that se 2000. I rechecked my measurements and the holes (from center of hole) is 4 1/16" and across the trim tab is about 3 3/4". i really appreciate you guys. I hope i get lucky [-o<