Search results

Hey everyone thanks for the nice comments. Couple of quick updates... In January, I had a local boat shop put on a cmc tilt and trim device. It is awesome!!! Will post a pic from my phone if I ever figure that out. Then two weeks ago I had to add a stainless steel prop because I had dinged...

Also, I might start another thread on this, but what would be the pros/cons of the flotation pods as opposed to something like Smart Tabs? I see a lot of praise for smart tabs and it certainly sounds like an easier/cheaper install and a good choice to get me up on plane faster and cruising more...

Response: 1. So far, it has gone everywhere my old 14' flat bottom jon went in the 5+ years I had it. Yes, it does draft a few inches deeper, but unless you're talking about tunnel hulls and jet outboards, I'm not sure that 3-4" is gonna make that much difference. So far it has not. 2. I don't...

You can look at all my work by following the link under my signature. I have pretty much finished working on this boat, except for two things: 1) I beach a lot on gravel bars and rocky shores. I have purchased a hull/keel protector from Cabelas and will install this coming weekend if it's warm...

Just a quick update - I have been fishing and enjoying this boat ALOT!!! It has also been used to haul a lot of people on different trips to my house on the Kentucky River. Whether it's a boat load of kids or beer drinking buddies, the boat has held its own. Was out on the river the other day...

thanks for all the very nice comments! Haven't been on here as much recently because I have actually been fishing and boating - imagine that, getting to actually USE the boat I've been working on for 5 months. Was up on my favorite trout river in central Kentucky. The boat did great. I have...

Whew! Finally am now "complete" with "major projects"!!! There will be plenty of minor things to fiddle with over time, but I'm done occupying the entire garage. (my wife is also happy with that). Got the carpet installed this weekend. It was hard to get perfect cuts and perfect fits because...

SlowRollin, It is a Porter Brand (PPG) two-part polyurethane. I will check the garage in the next day or so and see if I still have the can out there with a name on it. Will report back later.

Got a chance to do some major work this weekend. I held my breath, crossed my fingers and started measuring out the 3/4" piece of plywood I had purchased for my front deck section. Planning for the curvature of the boat's hull was complicated, but I was impressed with how well I did with my...

lots of updates... Got boat back from the boat shop with motor installed and lots of wiring and accessories. couple of views of the new look: console with steering wheel, and switches for bow and stern light, bilge, and cigarette lighter/12V charger, and fish finder on top: one of my...

Thanks for the kind words about the color scheme. That was the result of a LOT of hard work painting. IT's still not perfect, but good enough that the casual observer, not looking for errors, would find it satisfactory. Went turkey hunting last weekend and before I set off, I had my two hunting...

Sanded and repainted last night. There's still some sags that are visible in a certain light. But, I'm not a perfectionist. Got the boat flipped back over, right side up. Got some nice reflective numbers at Home Depot. It's coming together!!

Well... It's been a long couple of weeks. Again, weather turned cold and wet. I had the boat scheduled to be sprayed with an epoxy coating, but the day of that, temp plummeted into the mid 30s with freaking snow! The result was an awful paint job that I then spent quite a while sanding off...

Took some doing, but I got the boat interior totally cleaned out (took two nights with a box of rags and heavy-duty cleaning solution). Got heaters in the garage and cranked up, because - of course - the outside temp has plummeted and even snowed last night. That would happen when I"m finally...

Have been working steadily on the console build and then mounting the side controls. I've got the steering wheel and throttle lever where I can operate them comfortably from the seated position, or while standing. This is important to me because I run a lot of shallow, log-strewn rivers and I...

Well, one of my fishing buddies had a perfect solution. The motor currently has a hydraulic "gas assist" manual tilt feature. He suggested, why not just mount the motor to the transom and use it for a while to decide if a power tilt and trim is even that necessary. I made it for years with my...

hmmm... LonLB, you've got me rethinking some things. will make some updates on my build thread soon.

Ok, Well, at lunch I ran down to the boat shop that I've had work done in the past. to switch out the manual tilt and trim on my outboard itself with parts from Mercury to convert to power tilt and trim would be about $1000-$1200 for the parts and about $250 in labor. I have seen the exact...

It is a 15'6" v-hull, rated for 40 HP. The old evinrude I am replacing was 140lbs, with a newer mercury 40HP that weighs 175 lbs. I was planning on moving battery and some other things forward to counteract that extra 30lbs. (For instance, my 180lbs of operator weight will be fairly forward in...

Not sure if this should be in the Boat forum or Motor forum... Pretty soon I will be painting my boat (hopefully next week!), then onto the next step of putting motor on. It does not have power tilt and trim. I have talked to a local boat shop and they said they would install a CMC power tilt...