Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
If you are having any issues uploading or linking photos to your posts, send them to me and I will upload them and send you back the links to add to...
Last post
I changed the photo location. I will upload them to the TinBoats dedicated server. They will not be sitting on just any 3rd party hosting solution....
This is the running list of the current Sponsors. Help support TinBoats.net by supporting these guys first if you are shopping for similar products....
I am posting this from experiences I have had.I have been boating since I was in my early teens and fishing since I could hold a fishing pole.I used...
Last post
I'm no nautical engineer by any means but I have decked a few boats. The biggest factors to consider when doing decking is #1: Don't compromise the...
I just got off the phone with Fasco. Spoke with a nice lady but could not really understand her nor could she really help me. She gave me an email to...
Last post
I'd use the G-Flex 650, only $20 for a 2-part 4-ounce (each bottle) kit around here (Nor'East US). You will only be mixing a capfull of each to do a...
I'm all for not spreading Invasive species but this a load of BS. IMO anything like this should be part of the boat registration. Mandating that...
Last post
I just learned today that a number of counties in California have implemented a real time tracking system for boats. What little I know is that once...
Hi there, yesterday evening I picked up this 70s princecraft 11 footer. I wasn't expecting to buy a boat yesterday, but in my area they rarely pop up...
Last post
You can always use it and just not run it WOT; I'd just hate to see it get squirrely on you, never mind cause an insurance issue God forbid there was...
Hi all, new to the forums and after doing some searching and coming up with conflicting/inconclusive answers I figured I might as well just state my...
Last post
My grizzly 1648 has a 21 inch transom, which calls for a long shaft. I can only guess your sales person was confused.
Clearly the error is all...
Gents,
I have a 14' V, 25Hp Johnson, pin in the 3rd hole. Cav plate is level with the bottom. I'm getting 5,070 RPM with 1-person in the boat and...
Last post
I''m trying to achieve 5500 RPM because that's what the motor is rated for. I thought the motor height was critical and one of the first things that...
For what I’m planning on doing I’ll be blocking the little drainage channels that run under the ribs on my Lowe. I don’t want water building up there...
Last post
The Rule 900gph ‘LoPro’ picks up to maybe 1/2” and is automatic. I posted about it recently, found ‘em for $60-something shipped.
I'm continuing to run my Smokercraft as-is and have ideas for some nice to haves but should probably focus on things that will need attention sooner...
Last post
On fiberglass boats, we oversize drill the holes, fill with thickened epoxy and then drill again. That way any pass throughs or screws have an epoxy...
Did anyone else see this on the news? Right in front of me to the starboard and right in the area of an informal mooring area, 4 kids were dumped out...
Picked up a 2008 Lowe Roughneck 1448 a few days ago with a 25 hp Mercury. Pretty stoked. It's going to be an awesome river and small lake fishing...
Last post
Another thing those pumps are good for is in case you get caught in a down pour. It's happened to me twice and I do watch the weather. I don't go out...
I am new to the world of small metal boats. Most of my marine experience is on bigger stuff and jetskis and a little bit of hydroplane/small raceboat...
Last post
yesterday I remembered I had an old 6 gallon atwood tank stashed, so I dug it out and put it in the rear compartment. 2x 6 gallon tanks will work way...
Hi everyone. I have this 12’ crestliner . The bench seat wood Hass to be replaced. Looking at the old wood it had some sort of foam and vinyl...
Last post
I can't find any pics, but if you have the old bench seats then you've got a perfect template. Trace them onto new plywood and sand them really well...
