Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
This is the running list of the current Sponsors. Help support TinBoats.net by supporting these guys first if you are shopping for similar products....
Hopefully this guide will help you calculate the maximum amount of H.P. your boat can be insured for.
- This is to only be used as a guide.
- You can...
Last post
Using my 2017 Lowe 1040 the calculations come out as shown if I measure the transom width as in the graphic below. The calculations either come out...
Snagging a new '20 Zuke 60 and need correct SS prop choice. Hull, '00 Weld-Craft 1652 side console. 16'3 long with 18 factory transom pods for a 17'9...
Last post
Bought a SS 15 Powertech. See what happens in a couple weeks after the boat is rigged.
Have a 1983 35hp Evinrude that starts and runs seemingly okay but is consistently 70 psi on both cylinders. Should this be higher and what can I do,...
Last post
Well I got out today to try and start this morning and at least try to get it warm to retest compression... started first try so I got a videoZzz yes...
Ok so anyone who owns a 80's Johnson 20/25 has heard of being able to up the HP to a 30/35 well it can be done and I did it with very good results. I...
Last post
New/used lower housing should be here tomorrow. \:D/
Now, having dug into the two lower units I have on hand (76 35hp and a 84 25hp)I find that the...
Hi,
Looking at the boat below. Owner said the motor starts right up and runs great. Whenever I by an older motor I ususally change a bunch of stuff....
Last post
Correct PN for what?
The throttle being tight shouldnt be hard to fix. If you look on the end of the grip closest to the engine there should be a...
Hey everyone! So I've got a modified alumacraft 1442 ncs with a mercury 25hp that's on a cmc hydraulic jack plate. While at full throttle I get alot...
Last post
Looking at the photo you posted, I'd say two things, you need to trim her up some, the water directly behind the engine about 20-30' out should kind...
I am going on a road trip to pick up a used Mercury 40hp Jet Motor. I would like to at least temporarily mount it to my boat to test run and for the...
Last post
Most of the 40's use standard BIA 4 bolt mounting. SS fine thread is what I see a lot of, however Mercury sends coarse thread 1/2 SS bolts with...
Can anyone who has one share their thoughts on them? I've been considering getting one mainly for carbs, but my Chem Dip still does the trick so not...
Last post
Thanks for all of the replies. I'm def going to purchase one soon, but I will be going with a cheap model... at least initially.
Thought you guys might enjoy this. Did a routine service on a 17 Yamaha F70 mounted on a crappie boat (1754). Interesting setup; works great for the...
Last post
Must be why I see a lot of Yamaha outboards! And, I agree -- the lack of vibration is impressive.
Hello guys, I'm looking to buy a new aluminum prop for my 25HP Suzuki.
Any certain brands that I should steer clear of? I'm just looking for a decent...
Last post
Thanks Todd! I just looked up the Solas and it looks like exactly what I need at a good price.
Just had the motor basically rebuilt. When I took it out for the first time I'm getting very low output when I'm in forward. When in reverse it's...
Last post
Thanks for the replies. Sorry I wasn't specific enough, I'm pretty new at this. It's on a 1440 jon boat. The best way I know how to describe it is it...
2001 merc 15 four stroke. The carb was leaking fuel from the top and would flood the engine. Replaced the carb with a new carb. It ran fine for a day...
Last post
If it's leaking from a port on the top of the carb, it's most likely that the float needle is stuck in the open position. Since it happened on the...
05 merc 15 four stroke. The carb was rebuilt last fall, ran fine for a while. It wasn't run for about three months and now it's acting like the float...
Last post
You can try tapping on the bowl with a screwdriver handle or something like that.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
