This is the running list of the current Sponsors. Help support TinBoats.net by supporting these guys first if you are shopping for similar products....
Thought I would post this in another thread, May even be Sticky Worthy . Its about 15 minutes long, but very detailed and really helpful. This is for...
Last post
I watched #2 video. Wow, this is a fantastic how-to for guys like me. Certainly removed the mystery.
Should it be a two man job or can one guy do it reasonably easily?
Last post
I've done it both ways to a my last 2 boats/trailers. My 16' Lowe I swapped the rollers for bunks at the boat ramp with the boat in the water. On my...
Is anybody using a home made transom saver? I have been reading reviews on amazon and it seems that most of the new transom savers are failure prone....
Last post
As long as it stays connected until you want it off then life is good!
My current trailer, a Bear, for my G3 1756SC took another dump on me. This time it's the bottom bunks, out of nowhere, one side bunk just rotted when...
Last post
OK, in my opinion, it isn't really worth it to try to coat the 2x4's. 2x lumber is pretty cheap. You could probably replace them a few times for the...
Hey folks -- I am trying to replace the axle/springs on an old trailer I bought. I took the wheels off, measured the hub face and came up with 53&7/8...
I have a 2019 grizzly 1648 SC with a Merc 40hp 4 stroke outboard. It didn't come with a transom saver,instead you raise it up, and switch a lock over...
Last post
I installed new transom saver Fri. Took it to lake sat/sun and I feel it's a whole different animal. Rig feels solid to my vehicle. No bounce,wiggle...
I have a trailer that is slightly bent. it looks as if the previous owner had hooked a parking curb or something and then they pulled it forward and...
Last post
My Buddy got my trailer done, He welded in four new 3-inch channel beams after he straightened the frame he told me that it is 5/8 of an inch out of...
The old bunks that are carpeted on my sprint boat trailer are getting worn out and the carpet takes a couple of hours to drip off the water before I...
Last post
My boat only touches the composite deck boards. Treaded lumber is the framing only.
I have a trailer that I don't know the age of,the tires are 480x12.what would be a good replacement shock? i can feel it bouncing around, my boat is...
Last post
I honestly don't know the answer but one concern I would have (had) was that those shocks will be submerged. I understand they are sealed, but seems...
What are the best wiring and light kits you have found for your trailers? I am about to order one and want to make sure I get one that will last>...
Last post
Mine are pulled down the center of the rectangular galvanized tube framing. Rubber grommets are used where the wire(s) enter/exit the channels. This...
Any particular brand of tire covers you guys recommend for your boat trailer tires? I have 4.80-12 size tires, and that equals about 21 when mounted...
Last post
Dry Rot - The simple wood shield works!
Trailer Jacking - Lower tongue all the way you can, prop blocks under the rearmost support or frame, then...
I can't figure out how to attach the lights to the trailer. I went as far as opening one of the lights to see if there is a threaded hole in the back...
Last post
Thanks but that's not your burden. It woulda been nice had Wellmax provided better instructions. For future reference, you slide the head of the bolt...
I recently bought my first tin boat. On the trip home I noticed that the strakes (SP?) are contacting the wheel fenders, additionally the keel is...
Last post
I attached a pretty basic sketch of a typical trailer. My boat is supported by the two bunks and roller #1 which is under the bow stem of my boat. In...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
