Jet Boat Projects

New Topic

69 topics

Topics

Replies

Views

Last post

Global Announcements
SPONSORS

Last post by Jim « 18 Jun 2008, 09:23
Posted in Watering Hole

by Jim » 18 Jun 2008, 09:23 » in Watering Hole

This is the running list of the current Sponsors. Help support TinBoats.net by supporting these guys first if you are shopping for similar products....

0 Replies

131995 Views

Last post by Jim
18 Jun 2008, 09:23

Topics

Replies

Views

Last post

Topics
New boat build - 1648 Grizzly with 60/40 Jet

Last post by NVswitch « 23 Aug 2019, 21:56
Replies: 14
by Fishigan » 19 Jul 2019, 18:37

First post

Hey guys, I've been a lurker here a while but figured I'd share my new boat build. I got a very good deal on a lightly used 60/40 Mercury Fourstroke...

Last post

Cool Project

I just purchased a used Grizzley 1648 with a 30 hp Merc prop. i am converting it to a small fly fishing skiff.

1. I am also adding...

14 Replies

868 Views

Last post by NVswitch
23 Aug 2019, 21:56
Boat size for 1992 50/35 Johnson

Last post by jtf « 18 Jun 2019, 09:56
Replies: 6
by soky72 » 05 May 2019, 23:44

First post

I'm getting ready to pick up a new Weldbilt boat and was thinking about a 1752 but started reading online and now I'm not sure if my motor is enough...

Last post

I'm running a 1648 weldbilt with a 2 cycle Tohatsu 50/35. Goes as fast as I want to go. It uses more fuel than a prop. It's a modvee with not much...

6 Replies

1133 Views

Last post by jtf
18 Jun 2019, 09:56
What .... more Jet Jon questions ! Say it ain't so !

Last post by Kman1775 « 25 Mar 2019, 20:10
Replies: 4
by Kman1775 » 23 Mar 2019, 10:28

First post

Hey Guys thanks for having me .... I'm sure i'll enjoy being had !

Quick introduction.... I have many years fabracating and building high...

Last post

Well .... got down to the lake today to look at the wave rider up plan on using. The height of the motor is 19 1/2 inches the total length of the...

4 Replies

1090 Views

Last post by Kman1775
25 Mar 2019, 20:10
New member, new project...

Last post by Jim « 19 Feb 2019, 07:41
Replies: 20
by DirtyD » 09 Jul 2017, 20:06
1

2
First post

It's a 1448 monark with a 587, and 144mm pump with no trim. Used factory shoe, so it's 1 degree down...ish.

Last post

I'm going to talk to my forum guy to see if we can do something with these pictures...Some setting to adjust them on the fly to spin them.

Nice job...
20 Replies

9936 Views

Last post by Jim
19 Feb 2019, 07:41
Swim ladder

Last post by DaleH « 16 Dec 2018, 13:14
Replies: 2
by llbaker2 » 15 Jul 2018, 10:31

First post

IMG_20180715_084507649_HDR.jpg I just added a swim ladder to my 1752 Standard Blazer. I had total replacements on my left hip and right knee a few...

Last post

Here’s another option, for a permanent/secure mount, with no holes below the waterline either:

2 Replies

1481 Views

Last post by DaleH
16 Dec 2018, 13:14
New to forum have a few jet Jon questions

Last post by CedarRiverScooter « 23 Nov 2018, 22:33
Replies: 1
by CTilton » 23 Nov 2018, 22:11

First post

I am going to build a jet Jon using a late 90’s sea do gsx (free) and a tracker grizzly 1648 because of the .100 thickness on hull.

Main questions...

Last post

I don't have experience with Sea Doo you you could read all about them on Green Hulk or Iboat websites.

As far as engine placement, weight balance...

1 Replies

1067 Views

Last post by CedarRiverScooter
23 Nov 2018, 22:33
Alumacraft MV1448 Seadoo IB jet, Still jetting

Last post by JohnT « 13 Nov 2018, 19:40
Replies: 396
by Ranchero50 » 01 May 2009, 22:06
1

…

23

24

25

26

27
First post

Hey guys, first post. Got an invite to post my seadoo conversion as a thread here from one of your members. I bought a '92 Alumacraft MV1448 hull...

Last post

Hey Jamie , I'm glad to here you still have the jet , It's been awhile since I was on the site , I actually sold my tin boat and bought a glass boat,...
396 Replies

123524 Views

Last post by JohnT
13 Nov 2018, 19:40
Upgrade passive livewell help

Last post by richg99 « 22 Aug 2018, 18:44
Replies: 26
by llbaker2 » 20 Jul 2018, 15:48
1

2
First post

I recently bought my first boat. I got an aluminum 1752 flat bottom side console jon (Blazer Jet boat). Boat has two livewells, one under passenger...

Last post

I know next to nothing about livewells...however, I have observed a number of them that have a standpipe screwed into the bottom drain.

Way back...
26 Replies

7445 Views

Last post by richg99
22 Aug 2018, 18:44
ALUMA-JET- Duracraft 1648 SV Jetboat Conversion

Last post by PSG-1 « 04 Jul 2018, 18:03
Replies: 165
by PSG-1 » 17 Sep 2011, 00:46
1

…

8

9

10

11

12
First post

Here's some photos of my project that I did back in 2005:

It began as a 1997 DuraCraft 1648 SV that someone painted with copper paint and left in...

Last post

Good to hear from you again, mmf!

The specs say the 2472 sea ark weighs about 950 lbs, just the dry hull weight. Then you have to account for...
165 Replies

50136 Views

Last post by PSG-1
04 Jul 2018, 18:03
16/48 tracker refresher

Last post by xFORBESx « 15 Jun 2018, 15:23
Replies: 13
by xFORBESx » 30 May 2018, 19:47

First post

So I bought my boat a few years ago from a duck hunter that wanted it all came, so he stuck camp vinyl all over it, and painted the transom, and now...

Last post

Thank you, still a lot I want to get done but, it's getting there slowly.

Sent from my SM-G955U using Tapatalk

13 Replies

2998 Views

Last post by xFORBESx
15 Jun 2018, 15:23
Tuff Coat liner.

Last post by DaleH « 07 May 2018, 15:20
Replies: 2
by llbaker2 » 06 May 2018, 10:51

First post

Just finished putting Tuff Coat on the front deck of my new Blazer. Happy with the way it looks. Hope it last a few years. Went on pretty well but...

Last post

Well ... any good & lasting finish is definitely dependent on the prep, so we hope ya' done good! Looks great!

2 Replies

1381 Views

Last post by DaleH
07 May 2018, 15:20
Questions about jet jon's

Last post by mphelle « 30 Apr 2018, 23:36
Replies: 4
by sightfish » 30 Apr 2018, 12:49

First post

So I've run small aluminum boats with outboard jets (mostly an older 25 HP mercury 2 stroke) and am looking at options to upgrade. As you can imagine...

Last post

PM sent

4 Replies

1414 Views

Last post by mphelle
30 Apr 2018, 23:36
Where to put my Console.

Last post by Prowelder « 18 Mar 2018, 17:35
Replies: 14
by Tenner » 04 Jan 2018, 12:57

First post

Hey everyone. I am new to the forum but have been doing lots of reading for a while. I’m trying to decide what to do with my boat.

I have a Tracker...

Last post

What's your top speed ?

Sent from my SM-G955U using Tapatalk

14 Replies

5563 Views

Last post by Prowelder
18 Mar 2018, 17:35
Flotation pods? Do they help?

Last post by Ranchero50 « 18 Mar 2018, 09:00
Replies: 15
by GSPdog7 » 04 Sep 2017, 13:37
1

2
First post

Bought a 1754 Tracker with a 60/40 Merc on it and it runs 30 mph just by myself. I came from the bass boat world where my skeeter had literally no...

Last post

Pods trump tabs any day of the week. Pods work great to keep the arse end out of the water while you draft, something any outboard guy should love....
15 Replies

7223 Views

Last post by Ranchero50
18 Mar 2018, 09:00
New Boat Project - 1852 Lowe

Last post by Lonedrake « 10 Mar 2018, 16:24
Replies: 4
by Lonedrake » 24 Feb 2018, 23:29

First post

Picked up a Lowe 1852 this week. Went with another riveted boat because of the light weight. IMG_0599.JPG IMG_0601.JPG IMG_0604.JPG

Sent from my...

Last post

It’s an aluminum hatch off of an old tracker tx17 .

Sent from my iPhone using Tapatalk

4 Replies

1852 Views

Last post by Lonedrake
10 Mar 2018, 16:24
G3 1860 CCJ side panel removal

Last post by richg99 « 17 Feb 2018, 19:04
Replies: 1
by kthmarks » 16 Feb 2018, 19:22

First post

I thought I'd share with you (for the guys who have one), what's beneath the side panel after you drill out +/- 60 pop rivets. I installed a Minn...

Last post

That is good of you to post that information for the next guy.

t
Thanks

1 Replies

1280 Views

Last post by richg99
17 Feb 2018, 19:04
First jet john !

Last post by CedarRiverScooter « 09 Dec 2017, 09:24
Replies: 1
by Smitht144 » 08 Dec 2017, 22:26

First post

Hey guys doing my first jet john i got the boat and ski cut down and fit together looks pretty good what do i need to do before i seal them toghter ?...

Last post

Welcome to the site!

Without picts it is hard to give accurate advice.

How are you bracing the joint?

I used self etch primer on the aluminum...

1 Replies

1350 Views

Last post by CedarRiverScooter
09 Dec 2017, 09:24
spoon design for jetboats wanted

Last post by CedarRiverScooter « 07 Dec 2017, 21:52
Replies: 20
by brianb2247 » 29 Jun 2016, 16:50
1

2
First post

look some of you guys have great ideas on this forum and when a question is asked you usually redirect to someones build could some one pose me a pic...

Last post

That is best in class!
20 Replies

7495 Views

Last post by CedarRiverScooter
07 Dec 2017, 21:52
Stomp grate

Last post by CedarRiverScooter « 08 Oct 2017, 21:05
Replies: 2
by Dirtflorcraker » 27 Sep 2017, 21:33

First post

Hi. New guy here. Merging a 1999 Yamaha gp1200 with a 14x7 airboat hull. Has anyone here modified a budget minded stomp grate. I understand nothing...

Last post

See pg 11

2 Replies

1356 Views

Last post by CedarRiverScooter
08 Oct 2017, 21:05
16/48 Tracker w/ 110hp seadoo

Last post by CedarRiverScooter « 25 Sep 2017, 21:49
Replies: 11
by SC Designs » 28 Aug 2017, 08:21

First post

Hey guys, back at it again, got another build underway. Check out the pics.

Last post

Flat water is awesome!

Driving a jet jon is like water skiing without getting wet.

Next outing for us will be fall foliage cruise.

11 Replies

2330 Views

Last post by CedarRiverScooter
25 Sep 2017, 21:49
Alumacraft F Jet Build

Last post by IkeCarlson « 19 Sep 2017, 14:54
Replies: 19
by IkeCarlson » 26 Aug 2017, 02:03
1

2
First post

Ok, here we go. I am excited to get this under way, but nervous as all get out.

I picked up the jet ski today. It is a 1988 seadoo sp with a 587...

Last post

Pics!
19 Replies

3648 Views

Last post by IkeCarlson
19 Sep 2017, 14:54
16/48 Tracker w/ 145 HP

Last post by eshaw « 19 Sep 2017, 11:20
Replies: 38
by SC Designs » 16 Sep 2016, 09:35
1

2

3
First post

Alright guys, time to start another one. I sold my other Jetjon so its time to upgrade. I picked up a 2000 Kawasaki Ultra 150 that has the 1200cc...

Last post

Have you or do you know of anyone that has put twin skis into a 1872 welded jon?
38 Replies

10686 Views

Last post by eshaw
19 Sep 2017, 11:20
Jet john

Last post by Paintman « 13 Sep 2017, 18:43
Replies: 92
by Paintman » 30 Jan 2017, 17:28
1

…

3

4

5

6

7
First post

New to this forum,seems to be a lot of info here,just starting a jetboat project and have tons of questions,this is what I'm starting with,kawasaki...

Last post

It at the farthest point in the picture,I'm going to adjust it upwards next time I take the boat out,just trial and error I guess
92 Replies

13927 Views

Last post by Paintman
13 Sep 2017, 18:43
Help with jet jon

Last post by CedarRiverScooter « 07 Sep 2017, 19:59
Replies: 2
by dhousworth » 05 Sep 2017, 20:10

First post

I would like to build a jet jon but feel that I am just not qualified. Is there anyone that does this professionally, either doing it or helping me?

Last post

SC Designs builds them with owner supplied parts.

Look him up in the site directory & send him a PM.

2 Replies

1168 Views

Last post by CedarRiverScooter
07 Sep 2017, 19:59
14' Polar Kraft Jet Project

Last post by Flat_Bottum « 15 Aug 2017, 01:57
Replies: 44
by Flat_Bottum » 24 Feb 2015, 09:41
1

2

3
First post

Hello everyone, I just joined the site this evening. I have read a lot of threads from this site and since I am starting a project, I would like to...

Last post

All I did was get a piece of 1/4 aluminum, grind one edge to a knife edge and then cut slots in it so when I slide it up inside my grate it would...
44 Replies

12151 Views

Last post by Flat_Bottum
15 Aug 2017, 01:57
transom extension and trailer bunk redo

Last post by CedarRiverScooter « 21 Jul 2017, 08:51
Replies: 21
by handyandy » 16 Mar 2017, 10:01
1

2
First post

So my boat was short shaft 16 transom, and it started with a 40 prop tiller I ran for few years. Then added a jack plate which helped with shallow...

Last post

I would pack the wood holes with fiberglass & resin, then put some 3M5200 over that for good luck.
21 Replies

5228 Views

Last post by CedarRiverScooter
21 Jul 2017, 08:51
Paint for boat name

Last post by stinkfoot « 05 Apr 2017, 22:05
Replies: 3
by Boz Mon » 05 Apr 2017, 09:46

First post

I'm looking to stencil and paint on the name of my jet jon. Not sure if I need to use special paint or if anything will do. Has anyone done this? I...

Last post

I stencilled my numbers on with Rustoleum Painter's Touch Ultra Cover Matte Black. It's OK but there was a bit of bleed because I should have cut an...

3 Replies

1246 Views

Last post by stinkfoot
05 Apr 2017, 22:05
Mini rhino jet

Last post by brianb2247 « 09 Mar 2017, 17:53
Replies: 6
by brianb2247 » 03 Jan 2017, 16:10

First post

Building a mini rhino jet style in board jet the boat is 12' long 40 wide at bottom 48 at the top

Last post

640 tigershark monte carlo 1994

6 Replies

2106 Views

Last post by brianb2247
09 Mar 2017, 17:53
New B.. 16 ft manark, wave runner III gp

Last post by Jgarner9926 « 27 Feb 2017, 19:12
Replies: 4
by Jgarner9926 » 26 Feb 2017, 15:05

First post

So I'm new to this forum. But have been considering a jet John project for some time. I have read alot of the treads and I'm ready to start my...

Last post

Thanks for the great info. Sounds like a 760cc in the future. Will be posting pics as soon as I get into the build. Thanks again.

4 Replies

1386 Views

Last post by Jgarner9926
27 Feb 2017, 19:12
New member, jet Jon project, Engine identification.

Last post by tape204 « 23 Feb 2017, 17:48

by tape204 » 23 Feb 2017, 17:48

Hello all, I've been creeping around on this site for a couple years. Now it's time to seek some more specific help.

Alright token new member stuff...

0 Replies

1007 Views

Last post by tape204
23 Feb 2017, 17:48

New Topic

69 topics

Return to Board Index

Forum permissions

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum