This is the running list of the current Sponsors. Help support TinBoats.net by supporting these guys first if you are shopping for similar products....
Currently running an Alumacraft MV 1860 w a 50hp Merc 4 stroke, Atlas Micro Jacker, Solas 11p Stainless. I see 32mph right now with this set up....
Last post
An 1860 will be fine with a115/80 unless the boat is a pig weight wise, it won't scream, but it should plane out just fine. The funny thing a lot of...
I have a 90 HP outboard that has a weak throttle response when the control box is shifted into reverse. The forward has full throttle response. I...
Last post
It sounds like there is too much slack so if you can tighten that up, it should help the reverse, the start up lever and even forward should come in...
Got an 18’ Lund Jon. Tiller control. Gonna power it with a jet. How does Evinrude, Tahatsu, Mercury, Johnson and Yamaha 40 to 60 jets compare?
Thanks...
Last post
Does the boat have a tiller prop motor on it now? What size engine is on it? Usually you see 115/80 or 90/65 jets on 18ft boats but the 60/40 may...
It is surprising how little information that I can find about this engine. I'm considering putting it on a new build and I'm told that the difference...
Last post
The only differences in the 35 jet and the 40 jet are the stickers, price and programming. They are essentially the same engine. Mercury just...
I don't even know if this is possible, just checking to see if somebody has ever tried to do this? Probably will be giving Yamaha a call soon to see...
Last post
Agree totally with handyandy. Get a prop motor if that's what you use most of the time. Switching back and forth will get to be a PITA.
So I've got a 1993 20hp Johnson and I've come across a jet leg I should be able to pickup for under $500CAD, depending on condition. My current boat...
Last post
with a 180 lb boat, it should do just fine. the general suggestion is 25lbs per powerhead (not jet) horsepower
Hello guys. New to owning a jet outboard and I'm having a small issue and I hope I can get some input here. I bought a new blazer 1752 with a 60/40...
Last post
Agree, just knowing the basic ins and outs of the impeller, the liner, and the shimming process, is a big plus to a jet owner, pretty simple to do on...
My jet pump bearing grease hose has hole in it, should i just order one from outboard jets or is there something I can buy at local part store that I...
Last post
I've always had good luck ordering through them. I have always had the part numbers of the parts I needed though. Ship to the house in a couple days....
I sell boats built for Jet Outboards. They are built for me by a major manufacturer. Mostly what I sell are 1756 and 1856 semi-V hull boats with 4’...
Last post
This isn't a good picture but shows enough of my boat which has side rod trays and a side anchor release to the rear. Both Hyde and Koffler web pages...
1994 Johnson 50/35 on a riveted 1996 Tracker 1648. With 2 guys and fishing gear I use to get upper 20's spinning at 53-5400 rpm's. Nowadays I'm down...
I bought a 1980 Hewescraft River Runner and it came with an older broke 65 Johnson w/ a prop. I have a chance to pick up a strong running older 50hp...
Last post
I have a '94 Johnson 50/35 on a riveted mod-v 1648. Pretty thin hull and overall a light boat. Before I beat the crap out of the bottom, I was...
River Road Jet Boats partnered with Creature Craft Inflatables to make a white water running jet boat. These are pictures of the First Descent of the...
Need some help. I had a thread over on another forum where someone was kind enough to post Outboard Jets recommended tunnel design. That...
Last post
I used Outboard Jet's tunnel design for several years on the boats I sell but it is too short to protect the jet drive when trimmed all the way down....
Is this jet even worth considering? It's a 20hp which is just like the 18hp's that they built for years.
What size boat will it push? Will it plane...
Last post
As I said before they're are some select waters that have HP restrictions only ones I know of are some ozark rivers that limited to 25hp at the jet....
Had the boat out for the weekend, ran good Saturday, then on Sunday the motor died at full throttle, and would start up again. After a few minutes it...
Last post
Wiring can be so much fun! #-o My Mercury 60/45 came with a cut up wiring harness and the used controls I bought also had cut up and burned/melted...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
