Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
This is the running list of the current Sponsors. Help support TinBoats.net by supporting these guys first if you are shopping for similar products....
My jet pump bearing grease hose has hole in it, should i just order one from outboard jets or is there something I can buy at local part store that I...
Last post
I've always had good luck ordering through them. I have always had the part numbers of the parts I needed though. Ship to the house in a couple days....
I sell boats built for Jet Outboards. They are built for me by a major manufacturer. Mostly what I sell are 1756 and 1856 semi-V hull boats with 4’...
Last post
This isn't a good picture but shows enough of my boat which has side rod trays and a side anchor release to the rear. Both Hyde and Koffler web pages...
1994 Johnson 50/35 on a riveted 1996 Tracker 1648. With 2 guys and fishing gear I use to get upper 20's spinning at 53-5400 rpm's. Nowadays I'm down...
I bought a 1980 Hewescraft River Runner and it came with an older broke 65 Johnson w/ a prop. I have a chance to pick up a strong running older 50hp...
Last post
I have a '94 Johnson 50/35 on a riveted mod-v 1648. Pretty thin hull and overall a light boat. Before I beat the crap out of the bottom, I was...
River Road Jet Boats partnered with Creature Craft Inflatables to make a white water running jet boat. These are pictures of the First Descent of the...
Need some help. I had a thread over on another forum where someone was kind enough to post Outboard Jets recommended tunnel design. That...
Last post
I used Outboard Jet's tunnel design for several years on the boats I sell but it is too short to protect the jet drive when trimmed all the way down....
Is this jet even worth considering? It's a 20hp which is just like the 18hp's that they built for years.
What size boat will it push? Will it plane...
Last post
As I said before they're are some select waters that have HP restrictions only ones I know of are some ozark rivers that limited to 25hp at the jet....
Had the boat out for the weekend, ran good Saturday, then on Sunday the motor died at full throttle, and would start up again. After a few minutes it...
Last post
Wiring can be so much fun! #-o My Mercury 60/45 came with a cut up wiring harness and the used controls I bought also had cut up and burned/melted...
High all, hope everyone is getting out on the water or has plans to. Question, I have a 1998 mercury force 120 hp with outboard jet kit on it....
Last post
Thanks for the responses. I'll grab thoes numbers off the jet tonight. Dose anyone know roughly what a new e-tec 105 jet costs? Just trying to weigh...
I've got a good running 1999 Mercury 2-stroke 25 HP Jet that I want to sell. Just need more power. What do you all think it's worth? $1500.00 or so?
Last post
I’m located near auburn, al. Yeah we run it on a 1542 war eagle and get about 19 with one person and 13-15 ish with two guys about 190 a piece. . It...
Ok well here we go. I bought a 1754 grizzly jon boat last year with a 03 Yamaha 50hp 4-stroke tiller. The boat has the classic bench seat in the back...
Last post
60/40 Merc will be fine on that Grizzly. And carry a decent load. Plenty of guys running 60/40's on much bigger and heavier hulls. Plus depending on...
I recently added a Rockproof jet foot, and I'm getting alot of spray from it. Any one else have this issue?
Last post
flapper works on poly, just can't really stick it to it as it will get hot kind of melt and gum up the flapper. Hand files work for more fine tuning,...
i picked up a new blazer with a factory merc 40 jet that has smoked at start up since day 1.i called the dealer and asked them about it and was told...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum