Homemade power pole

TinBoats.net

Help Support TinBoats.net:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Ranger J.

Active member
Joined
Apr 26, 2015
Messages
31
Reaction score
0
Location
Brighton, TN
Hey everyone, I am working on making my own homemade power pole for my Tracker 195. I am using 3" channel aluminum, HDPE plastic, 225 lb 12v linear actuator, 3/4" fiberglass pole with a metal base tip, and a wireless remote. I worked on it all day today, and for a few hours yesterday. I made decent progress on the main body.
 

Attachments

  • IMG_1504.JPG
    IMG_1504.JPG
    68.3 KB · Views: 8,244
  • IMG_1500.JPG
    IMG_1500.JPG
    87.4 KB · Views: 8,245
  • IMG_1502.JPG
    IMG_1502.JPG
    78.5 KB · Views: 8,242
  • IMG_1497.JPG
    IMG_1497.JPG
    46.6 KB · Views: 8,242
  • IMG_1503.JPG
    IMG_1503.JPG
    55.3 KB · Views: 8,242
  • image.jpg
    image.jpg
    21.5 KB · Views: 8,244
  • image.jpg
    image.jpg
    47.6 KB · Views: 8,244
Put in some more work today. Got the pole moving. Video won't upload, will try to get more pictures tomorrow and install the fiberglass pole.
 
I found it on Amazon. I bought the fiberglass pole, tip, actuator, and remote from Amazon. It's water resistant. It will extend out 12"
 
Alright, I got the pole test mounted on the boat, and tested the remote. I found that I miss measured making the mounting bracket. The poles sit at 22 degree angle instead as close to 90 as I thought, but I will work on that tomorrow. I am also considering reducing the length of the poles or drilling holes to reduce the weight. I bought the clamp on base for the power pole micro anchor to use for mounting the poles. I'm not too keen on drilling holes in my boat. I had to cut out a hole in one of the poles to allow the actuator to fit in between the two. I am probably going to switch the arms around so that the hole faces the boat instead of away due to the wire rubbing the inside of he channel. Or I will make a wider hole.

I don't know why my pictures are posting sideways.
 

Attachments

  • IMG_1516.JPG
    IMG_1516.JPG
    43.9 KB · Views: 7,976
  • IMG_1517.JPG
    IMG_1517.JPG
    81.2 KB · Views: 7,977
  • IMG_1518.JPG
    IMG_1518.JPG
    40.4 KB · Views: 7,978
  • IMG_1519.JPG
    IMG_1519.JPG
    118.7 KB · Views: 7,977
  • IMG_1520.JPG
    IMG_1520.JPG
    83.9 KB · Views: 7,978
I got the angle of the pole fixed. I didn't take into consideration the the dead rise of the transom.
 

Attachments

  • IMG_1524.JPG
    IMG_1524.JPG
    79.9 KB · Views: 7,942
I got the pole mounted today. I took it out and tested it, and the pole has a lot of flex. It held the boat well in soft to semi hard bottom, but was not as stable in gravel. The metal tip actually echoed pretty loud across the gravel. I am going to cut the arms down from 6' to 4' tomorrow, and cut the pole from 8' to 4'. I swapped the arms locations so that the actuator motor faced the boat instead of away, and allows the wire to move freely without rubbing the arm. You can see the brackets I made for the base to attach the pole to the clamp. These were made out of a piece of channel I cut in half, and made a 22 degree cut to make room for the arms. The bolts used for the pivot brackets and to attach the base bracket to the arms are 3/8", and the bolts used to attach the actuator and the clamp base are 5/16". All the nuts used are thread locking. The pole system is sturdy during travel. I still can't get my videos to post.

I should clarify that the flex I was referring to was if the boat was moving when the pole hits bottom. I am also going to find a better way to secure the fiberglass pole to the top bracket.
 

Attachments

  • IMG_1530.JPG
    IMG_1530.JPG
    121 KB · Views: 7,923
  • IMG_1527.JPG
    IMG_1527.JPG
    82.5 KB · Views: 7,922
  • IMG_1531.JPG
    IMG_1531.JPG
    124.2 KB · Views: 7,921
  • IMG_1533.JPG
    IMG_1533.JPG
    53.8 KB · Views: 7,922
Well, I got the pole secured, and everything wired up. I left the arms at 6' for the time being, but cut the fiberglass pole from 8' to 6'. Now I am going to paint it black or blue, I can't decide which would look better.
 

Attachments

  • IMG_1543.JPG
    IMG_1543.JPG
    34.4 KB · Views: 3,092
  • IMG_1544.JPG
    IMG_1544.JPG
    60.7 KB · Views: 3,092
[youtube]https://youtu.be/CO32yb2Af78[/youtube]
Hopefully this works for y'all. I uploaded it to my YouTube. I will get another video of in the water this weekend.
 
rednecknproud21 said:
I love it how much would you say you have in this build and where did you get the supplies from

Sent from my XT1254 using Tapatalk

I got the aluminum from a metal distributor, Ryerson steel $145. The actuator, control, aluminum tip, and fiberglass pole came from Amazon.com $190. Bolts and nuts all came from Lowes $90. The clamp base came from bass pro for $60. So about a total of $485. It was a fun build. I will likely remake the top knuckle, and possibly the bottom one. And add a cost of paint.
 

Latest posts

Top