12ft Sunray shallow v

TinBoats.net

Help Support TinBoats.net:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
This summer running the local rivers I have found a few places that hold ducks. So the boat will be pulling double duty this year. 21 days to go!
 

Attachments

  • IMG_20180923_141707426.jpg
    IMG_20180923_141707426.jpg
    146.8 KB · Views: 2,228
I realized that I never posted possibly my favorite improvement. New oarlock socket inserts and oarlock risers. The inserts are plastic and inexpensive and the risers are just cut up original locks with some tubing welded in and washers to keep wear to the inserts minimal. Silent. No creaks whatsoever, a pet peeve of mine. Anyone who rows to drift rivers or go across ponds should consider this. A 5/8" drill bit to drill out the old brass inserts will be the most expensive part at around $25, if you can't find one to borrow.
 

Attachments

  • IMG_20181103_145401407.jpg
    IMG_20181103_145401407.jpg
    29.3 KB · Views: 2,096
  • IMG_20181103_145410116.jpg
    IMG_20181103_145410116.jpg
    43.9 KB · Views: 2,096
Where did you buy that aluminum? And how did you know how to fasten it inside the boat, etc.? And how did you cut it?

I want to venture out and have a few ideas for my 12 footer...just not sure where to start.
 
The aluminum I bought at a place called metal supermarket, they had any size needed. 6061 1x1x.125 angle for the floor bracing. I used 1.5x1.5 and 2x2 both quarter thick for the side bracing and the front cross support. I am fortunate enough to have a friend with a metal shop in his garage. So to cut we used an automatic metal cutting bandsaw, but a vise and sawzall would work as well. All of the aluminum on the floor is attached with 3/16" rivets into the ribs of the hull. The side supports are bolted with 1/4x20 ss machine screws, washers and nyloc nuts through the original front seat support and welded to some more of that 1x1 1/8th inch that is riveted to the original rear seat. The front cross support is welded to the side supports. All of the welding was done with a mig with a spool gun. I hope that answered some questions. Ask any others that come to mind. I did a lot of reading on here, measuring and thinking about layout and pricing a parts list before I started collecting parts. Once I had most of the parts I started the project. That way I wouldn't get stuck with it half done and possibly unable to afford what I needed to finish quickly.
 
I haven't updated this in 3/4 of a year. This spring I picked up a 78 Evinrude 15hp longshaft from a friend. We did a little trading and I ended up getting a good deal on it. The first thing I did was pull the lower unit, cleaned it up a bit and replaced the water pump. Took the driveshaft to a friend up a friend and had him use his lathe to cut a section out of the middle and machined it to a peg and socket essentially before welding it back together at short shaft length. I took a hacksaw to the shift linkage to shorten that and cut the slot for the retention screw. Bolted all that up and finished by replacing the thermostat, which happened to be stuck open. Boat runs 22mph by myself with 3 gallons of fuel and a group 27 battery
 

Attachments

  • IMG_20190716_165404470.jpg
    IMG_20190716_165404470.jpg
    3.3 MB · Views: 987
To handle the extra thrust and weight of the new motor I rebuilt the transom again. I didn't like the way I did it before so it was a good opportunity to clean it up. 3/4 acx construction adhesived into an inch and a half thick piece. Then 1.75x.125 6063 channel cut, fit and welded with a spool gun to act as the transom cap, but also stiffens the transom immensely. All lights were wired in, solder and adhesive heat shrink for that.
 

Attachments

  • IMG_20190608_170152343_HDR.jpg
    IMG_20190608_170152343_HDR.jpg
    3.1 MB · Views: 987
  • IMG_20190608_173922196.jpg
    IMG_20190608_173922196.jpg
    3.8 MB · Views: 987
  • IMG_20190608_202154341.jpg
    IMG_20190608_202154341.jpg
    3.9 MB · Views: 987
  • IMG_20190602_153647460.jpg
    IMG_20190602_153647460.jpg
    3.9 MB · Views: 987
  • IMG_20190608_232923924.jpg
    IMG_20190608_232923924.jpg
    3.6 MB · Views: 987
Then over the last week I've been painting, since I apparently like to work backwards. Washed, wet sanded then wiped with vinegar/water. Followed that with rustoleum clean metal primer and Rust-Oleum flat brown. Finished it off with redleg stencils and 4 colors of spray paint. Last picture is my daughter relaxing in the boat :D
 

Attachments

  • IMG_20190831_182901375.jpg
    IMG_20190831_182901375.jpg
    4.6 MB · Views: 987
  • IMG_20190824_182108255.jpg
    IMG_20190824_182108255.jpg
    4.1 MB · Views: 987
  • IMG_20190824_141134493.jpg
    IMG_20190824_141134493.jpg
    3.7 MB · Views: 987
  • IMG_20190720_080438646.jpg
    IMG_20190720_080438646.jpg
    3.6 MB · Views: 987
The front is more of a seat than a deck. Standing on the floor feels more stable than it did standing on the ribs, probably just because it's flat. It's possible to stand all the way in the front, but I wouldn't do it while fishing. Pic is of the boat being grassed in with the "layout" style blind I stuck on it this year.
 

Attachments

  • IMG_20190905_191252495.jpg
    IMG_20190905_191252495.jpg
    4.2 MB · Views: 943
Have you considered using underneath the two sides of the deck for storage? Looks like a good place to put extra gear or cargo netting or something. The front of the deck looks like it makes getting in a and out of the boat at shore very easy. Nice job.
 
That's generally what it ends up being anyways, right now the dekes get stacked over there but some netting or pockets would be a perfect addition. The front deck does make it easy to hop out without a dock. Thanks for the kind words. Raffia showed up the other day so I grassed it all in today.
 
Nice buildup! Any more pics of your engine conversion from long to short shaft? Thanks for the inspiration!

- B
 
Thank you! The carpet is no longer clean and the paint is scratched from most of the local launches having no docks, but it is a great boat. As far as the shaft length conversion, Leeroy's write up is far more thorough than I could ever remember to type up. https://www.leeroysramblings.com/OMC-Converting_shafts.htm
 

Latest posts

Top