TinBoats.net
The original aluminum boat site!
Forums
New posts
Search forums
Blog
What's new
New posts
New media
New media comments
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Install the app
Install
Forums
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Help Support TinBoats.net:
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
M
MDCrappie
Well-known member
·
From
Middle River, Md
Joined
Dec 12, 2007
Last seen
Yesterday at 8:08 PM
Messages
213
Reaction score
37
Find
Find content
Find all content by MDCrappie
Find all threads by MDCrappie
Latest activity
Postings
About
M
MDCrappie
replied to the thread
Is the motor height going to be an issue?
.
Classic symptom of motor mounted too low. Proper way to correct is to raise the motor. When I bought my Carolina skiff 16 you could not...
Yesterday at 6:50 AM
M
MDCrappie
replied to the thread
NGK BUHW2- vs - Champion L78V
.
No experience in an outboard, but when I used to have a CR250R honda the NGK would run for weeks and when I put a Champion in it would...
Thursday at 6:06 AM
M
MDCrappie
replied to the thread
Johnson 6 Project
.
I would think it to be OK as long as you don't damage any of the teeth. Or if pulling from top don't damage the rope groove.
Wednesday at 6:59 AM
M
MDCrappie
replied to the thread
Johnson 6 Project
.
Can you get one of those 3 armed pulley pullers on that pull from the edge?
Tuesday at 7:25 PM
M
MDCrappie
replied to the thread
Is the motor height going to be an issue?
.
I don't remember exactly where it sits now and the motor is in the shed. What I did though was raised the motor 1/2" at a time. Got to...
Tuesday at 7:23 PM
M
MDCrappie
replied to the thread
Lithium battery - worth the expense?
.
Pretty sure it's a progression thing with the manufacturing. Started out fitting into the 31 case and now able to compact things and get...
Tuesday at 5:55 AM
M
MDCrappie
replied to the thread
Is the motor height going to be an issue?
.
Get some plate and bolt together. Or get someone to bend some plate for you. Either into a "c" or two pieces into "L" and sandwich...
Tuesday at 5:52 AM
M
MDCrappie
replied to the thread
Yamaha 25hp 14ft semi-V rpm range question
.
You're definitely not set up correctly, or you are WAY overloaded. Can you take a picture of the stern with the motor in running...
Sunday at 6:42 AM
M
MDCrappie
replied to the thread
Mid 1980’s Mercury 35 wire corrosion
.
I've never tried, but doubt there is. It's vinyl I believe.
Sunday at 6:35 AM
M
MDCrappie
replied to the thread
Lithium battery - worth the expense?
.
Just got back from fishing and you did NOT just make a statement, you asked a QUESTION. May not have been directly towards me, but...
Apr 18, 2024
M
MDCrappie
replied to the thread
Mid 1980’s Mercury 35 wire corrosion
.
Store it upside down. Lid will be a little harder to get off but it won't dry up. These lids, especially after using channel locks to...
Apr 18, 2024
M
MDCrappie
replied to the thread
Thread type
.
His thread is straight (parallel), 3/4" npt is tapered. I think he needs a female in 3/4-14 NPSM Something like this...
Apr 17, 2024
M
MDCrappie
replied to the thread
Thread type
.
The problem I think he will run into is that most of those fittings are tapered. His threads are straight. About the only 3/4" straight...
Apr 17, 2024
M
MDCrappie
replied to the thread
Thread type
.
I figured it out years ago when I purchased a screen strainer for one...
Apr 17, 2024
M
MDCrappie
reacted to
Gilby's post
in the thread
Thread type
with
Like
.
Yes, that is what I am talking about. I knew it was 3/4'' just wasn't sure on thread pitch. Thank you!!
Apr 17, 2024
Loading…
Loading…
Forums
Members
Top