Search results

My guess is they were for anchor mate lines. My 72 Monarch has 4, 2 on each side with the anchor lines running through them.

Buy bulk and a HVLP gun and spray it. way cheaper and you'll need to put a finish coat on it next. Now you will have the gun to spray the top coat with!!

This will be a great boat for you! If you want some solid aluminum rivets to use on the angle brackets pm me your name and mailing info. I have a pound of them that will take me the next 40 years to burn up. I would be happy to mail you a handful.

If you need rivets I bought the smallest quantity of 3/16 solid rivets from Hansen 1 lb about 400 rivets. I would be happy to mail you a handful. PM me and we can get them to you.

sea Foam has a rust buster out that works well. As some one else said in an earlier post, spray sever times over a few hours. You will get them loose!

The old fashion way. Angle grinder and cone brush for the worst of it and then 100 grit sand paper and a sanding block. Washed it with an aluminum cleaner / etching product prior to prime and paint. It really paid off. The interior paint is really tough and hard to scratch off, Same with the...

Thanks guy's. I did the trailer rebuild as well. Added 5 feet of trailer tongue and every nut, washer, bolt, bearing and wire is new. I'm happy that I put in the work.

I started this project last year in August. It's been in the water for a few months now. It turned out pretty well. Learned a lot in the process. Thanks to all of you gents who answered questions, gave advice, and some needed motivation at times. Now I'm looking for a 16' to go to work on!

I have a new to me Johnson 15hp Model # 15R79E. I'm assuming it's a 1979 model. It has sat for about a year. Prior owner said it ran very well....... I kept it in heated storage this winter and when I got my boat done in August bought a new fuel tank and fuel line, fresh gas and plugs. It...

Thanks for the feed back. I am setting them at the 1.5 inch mark and will check them after a few loadings. Thanks to all of your responses.

I would like some feed back on the placement of guide bunks or side bunks. How much space is normally allowable or needed between the width of the boat and the bunks?

I would like some feed back on the placement of guide bunks or side bunks. How much space is normally allowable or needed between the width of the boat and the bunks?

Hey guy's, I'm looking for some advice on trolling motor size. I am just finishing a 14 ft Monarch flat bottom and will next need to equip it with a electric motor ( main power 15hp Johnson). I am not sure that I want a bow mount so I am focused on a transom mount for now. I will mostly use...

Hey guy's, I'm looking for some advice on trolling motor size. I am just finishing a 14 ft Monarch flat bottom and will next need to equip it with a electric motor ( main power 15hp Johnson). I am not sure that I want a bow mount so I am focused on a transom mount for now. I will mostly use...

Many thanks I will check these out.

Hi Guy's, Any suggestions where I should hunt for a replacement fuel pump for my Johnson 9.5 h.p. One of the plastic nipple connectors for fuel inlet or outlet broke and I need to replace the assembly. Any help would be much appreciated. I tried O'rielly Auto parts but no luck there. Used to...

I have a 2 stroke merc 5 hp that has internal or external tank. Runs all day on a gallon of fuel, starts first pull, exhaust's through the prop so it's really quiet. It idles so slow you can leave it in gear at the dock and still hang on the dock. I use it on an 15' foot inflatable most of the...

what part of SD are you from? We come out once a year for a week or so. I know the fishing is good and would like to do some fishing while we are there. Normally we stay south of Rapid City. Great looking eye's

I recently purchased 3/16 diameter by 3/8 length round head rivets from Hanson rivet company. 1 pound bag that they said would have 450 rivets. I would be happy to send you as many as you need. I don't think I will ever come close to using these even if I rebuild several more boats. Hanson also...

why don't sharks bite attorneys? Professional courtesy!